Ashly 24.24M Manuel d'utilisateur télécharger pdf (Page 1)

Operating Manual - WR-5 Remote Control

WR-5 User Reference

1. Introduction:

The WR-5 is a microprocessor based remote control unit for the Protea 24.24M, Ashly’s multi-

channel DSP matrix processor. The WR-5 is designed to fit into a standard electrical wall box for

remote control of assignable 24.24M functions. Each of six buttons on the WR-5 can be pro-

grammed to engage one of the following functions: preset recall/scroll, channel volume, mute, or

zone source selection. Programming of each button is done from software, when the WR-5 is con-

nected to its host 24.24M, and the 24.24M is in turn connected to a PC using Protea System Software

(version 6.4 or greater). Multiple WR-5 units can be daisy-chained from the same 24.24M for

discrete control over multiple locations under the processing control of one 24.24M.

Installations which currently use WR-3 or WR-4 units can integrate a WR-5, but special wiring

requirements apply (see section 3). For new installations, Ashly recommends exclusive use of the

WR-5.

2. WR-5 Features:

The WR-5 can be thought of

primarily as a programmable zone

controller. The physical acoustic space

in which one WR-5 is installed is gener-

ally considered one zone, driven by a

24.24M output or group of outputs.

The WR-5 has six programmable

buttons, each with its own status LED.

Button programming is done in Protea

System Software (V6.4 or higher).

There is a pocket in the mylar overlay to

the right of each button for a paper label

to be inserted. The two up/down buttons

adjust overall zone volume level (if

programmed) or individual button

parameters. The numeric LED displays

zone volume level, button/function

values, or status/diagnostic indicators.

On the back of the WR-5 unit, two four pin euroblock connectors are used for data INPUT from

a 24.24M, or LINK for connecting to another WR-5. There is also a two pin jumper labelled “J6”

which requires the provided female jumper to be installed if the WR-5 is the last one in the data

chain.

3. Wiring and Mounting a WR-5:

All wire connections between a WR-5 and the 24.24M use a two-piece euroblock connectors, a

screw-terminal plug for the wire connections, and the mating jack on the product itself.

ASHLY WR-5

1 2 3 4

Résumé du contenu

Page 1 - WR-5 User Reference

1Operating Manual - WR-5 Remote ControlWR-5 User Reference1. Introduction:The WR-5 is a microprocessor based remote control unit for the Protea 24.24

Page 2 - Wiring a WR-5 to a 24.24M

Operating Manual - WR-5 Remote Control2The WR-5 uses a four conductorserial bus to connect to the 24.24M andto subsequent WR-5 units, with a serialbus

Page 3 - 5. Programming the WR-5:

3Operating Manual - WR-5 Remote Control4. Getting StartedThe WR-5 comes with no configuration, therefore it must be programmed using Protea SystemSof

Page 4

Operating Manual - WR-5 Remote Control4seven seconds, also locking out any other WR-5 action for that time.3) Preset Scroll Mode - A range of 24.24M

Plus de documents pour Processeurs Ashly 24.24M

Voir le document Ashly 24.24M Spécifications

Ashly 24.24M Spécifications (28 pages)

Commentaires sur ces manuels

Pas de commentaire

Ashly 24.24M Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Processeurs Ashly 24.24M. WR-5 Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Processeurs Ashly 24.24M

Commentaires sur ces manuels

Ashly 24.24M Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Processeurs Ashly 24.24M. WR-5 Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Processeurs Ashly 24.24M

Commentaires sur ces manuels

Produits connexes et manuels pour Processeurs Ashly 24.24M